Distilleries

Stainless-Steel-Distillery

Stainless steel and copper distillation equipment

Here we list all distillers, regardless of whether they are intended for alcohol distillation or steam distillation for the production of essential oils. With our distillers, you can distil anything, but we have models that are optimised for alcohol and others for essential oils. If you want to do both, choose an all-rounder.

All devices must be rinsed before use; after assembly, they should only be cleaned roughly.


GPSR information and manufacturer's instructions: 

Information on copper stills can be found in the respective articles at the end of the article descriptions.

The following information applies to all our stainless steel distillation equipment

Hazard warning: When used properly, our stainless steel distillers do not pose any particular hazards. All our devices are designed so that high pressures cannot build up. However, you should be aware that all parts become hot during distillation . We therefore strongly recommend wearing protective gloves and safety goggles during distillation, refilling and dismantling. When using gas burners, only devices with a safety pilot flame should be used. Gas appliances used indoors must be approved for indoor use. Please be careful and follow the downloadable instructions for use.Verdana,Geneva,sans-serif">Please be careful and observe the downloadable instructions for use.

Manufacturer's address:

herstellerangebote.de - Zerbster Str. 15 - 39279 Leitzkau - Germany, email address: support(ad)herstellerangebote.de

Accessory set with pump for stailess-steel smaller stills up to 2 litres

Accessory set with pump for stailess-steel stills up to 2 literes

This set includes everything you need to be able to distil immediately and seriously with our stainless stills up to about 10 liters. 

  1. 20 liter plastic bucket with lid as a cooling water reservoir.

  2. Powerful 230 volt cooling water pump, sufficient for all our stainless steel stills up to 2 liters.

  3. Various PVC hoses of 2m each, including 2 hoses with hose screw connections for the still cooler. In addition, 2 hoses of different thicknesses for different applications.

  4. Plastic tap for cooling water regulation, suitable for the walking flow cooler.

  5. Graduated 100 ml measuring cylinder with foot to be able to safely collect and measure the distillate.

  6. Cleaning brush.

  7. Floating thermometer for checking the cooling water if you let the hot waste water run back into the bucket. Above 40°C, the water should either be cooled with ice or changed.

  8. A roll of Teflon tape for sealing, e.g. if a seal becomes defective during distillation.

EUR 55,00
incl. 19% tax excl. Shipping costs
accessory-set

Accessory set with pump for miniature copper stills up to 3 litres - Not suitable for our stainless steel stills


This set includes everything you need to be able to distil immediately and seriously with our stills up to about 3 litres. The pump is powerful enough to safely supply even all mini nestling in the range 0,5 to 3 litres size (as they may be used legally in Austria and from 2018 Germany or Switzerland) with cooling water. First and foremost, the set contains a functionally-sized cooling system for the still, but there are also other accessories for cleaning and sealing. In addition, when purchasing a stainless steel still together with the accessory set the right hose fittings for our coolers are there.
The set includes a 10-liter plastic tub as a cooling water depot (the water must be replaced several times in larger distilleries), plus a 230-volt cooling water pump, plus several meters of food-grade tubing in four different sizes so you can safely connect any distillery. The hoses can be partially inserted into each other and can thus also bridge different connections and adapters. In addition, a cleaning brush, a swim thermometer, a roll of Teflon tape for sealing the still and a 100 ml graduated cylinder to the distillate safely collecting and measuring.

EUR 47,00
incl. 19% tax excl. Shipping costs
Cooling-Water-Hosepipes

Set of Textures Hosepipe for Distillery
2 Hosepipes , 3 m long:

1/2" - 3/4" und 1/2" - 1/2"

Two times 3 m long crease resilent PVC-Textures-Hosepipe with fitting screw-connection using between cooler of distillery (1/2") and your home connection.

EUR 30,00
incl. 19% tax excl. Shipping costs
Cooling-Water-Hosepipes

Set of Textures Hosepipe for Distillery
2 Hosepipes , 2m long:

1/2" - 3/4" und 1/2" - 1/2"

Two times 2 m long crease resilent PVC-Textures-Hosepipe with fitting screw-connection using between cooler of distillery (1/2") and your home connection.

EUR 25,00
incl. 19% tax excl. Shipping costs
Seals

Spare Parts for our Distilleries you can find here:

Spare Parts for our Distilleries

EUR 0,00
incl. 0% tax excl. Shipping costs
33 to 38 (from a total of 38)

Hinweis:

Für die Herstellung von z. B. Hydrolaten, ätherischen Ölen, destilliertem Wasser usw. dürfen Sie auch als Privatperson Geräte erwerben und besitzen. Bis zu 2 Litern Kesselvolumen sind diese meldefrei.