DESTILLIERMEISTER ECO Series
Distillate for steam distillation for the production of essential oil
- Water-/steam-boiler: 7 to 11 liters,
- Plant basket: 3.5 to 6 liters,
- dome lid to reduce back dripping losses,
- counter-flow performance cooler
- Lockable with fasteners,
- Hygiene by stainless steel - no verdigris danger.
Stainless steel apparatus
Equipment
Delivery
-
Water-/steam-boiler: 7 to 11 liters, suitable for all fireplaces.
-
Plant basket: 3.5 to 6 liters,
-
dome lid with plug-socket (3.1) and fasteners (3.2).
-
Stainless steel distillation bridge with a power-counterflow-cooler. The cooling length with depentent from the model comfortable 70 to 80 cm, resulting in a significantly lower water consumption results than the previous model with Liebig cooler.
The two ends of the cooler (T-pieces) are made of copper, the screw nipple made of gunmetal. These come exclusively with cooling water in touch.-
Thermometer socket.
-
Curved double tube. In the soul flows the distillate and between soul and mantle the cooling water in opposite direction.
-
Cooling water inlet.
-
Cooling water outlet.
-
Distillate outlet.
-
-
Still thermometer and silicone-plug. Laboratory thermometer with red filling and silicone stopper. When first inserting the thermometer into the stopper, rub a drop of cooking oil onto the red end. The thermometer is pushed through the hole in the stopper from the thick to the thin side until the black mark on the thermometer at the bottom end of the stopper is just visible; this is the immersion depth of the thermometer.
or 2 plant baskets
Supply
Scope of delivery
-
Water-/steam-boiler: 7 to 11 liters, suitable for all fireplaces.
-
1st Plant basket: 3.5 to 6 liters,
-
2nd Plant basket: 3.5 to 6 liters.
-
dome lid with plug-socket (4.1) and fasteners (4.2).
-
Stainless steel distillation bridge with a power-counterflow-cooler. The cooling length with depentent from the model comfortable 70 to 80 cm, resulting in a significantly lower water consumption results than the previous model with Liebig cooler.
The two ends of the cooler (T-pieces) are made of copper, the screw nipple made of gunmetal. These come exclusively with cooling water in touch.-
Riser pipe
-
Thermometer socket.
-
Curved double tube. In the soul flows the distillate and between soul and mantle the cooling water in opposite direction.
-
Cooling water inlet.
-
Cooling water outlet.
-
Distillate outlet.
-
-
Still thermometer and silicone-plug. Laboratory thermometer with red filling and silicone stopper. When first inserting the thermometer into the stopper, rub a drop of cooking oil onto the red end. The thermometer is pushed through the hole in the stopper from the thick to the thin side until the black mark on the thermometer at the bottom end of the stopper is just visible; this is the immersion depth of the thermometer.
Instructions for using the stills:
The systems with 2 baskets can be used modularly. For smaller quantities of plants, a plant basket is left out. The toggles are adjustable and take that into account.
The ideal filling height of the plant baskets should be determined specifically by experiment, depending on the plant or drug. In the case of fine material, attention should be paid to loose filling. The best results are usually achieved when the baskets are filled to the top. In the case of coarser material with a low bulk density, the plant matter can still be heaped into the helmet and slightly compacted, especially in the case of fresh material. For the distillation of oily wood, the material should be prepared planed into thin shavings.
The exact distillation time and the withdrawal quantity depends on several factors. these are:
- the heating power,
- the plant variety,
- the plant basket volumes.
The minimum heating power should be 1400 watts,
the heating output must be all the higher, primarily: the larger the diameter of the plant basket. For the present models, this means e.g. B.: If you heat with approx. 1500 watts of induction heating at 22 cm, you need approx. 1800 watts at 24 cm and 2000 watts at 26 cm. Secondary: The greater the dumping height. However, this only applies if the dumping height is high enough. If the filling height is too low, it can happen that the steam flows through the product to be distilled without dissolving the essential oils due to its dynamics if the heat output is too high. With a lower bulk height, it makes sense to compact the material to be distilled more. A larger bed height is, to some extent, better than a smaller one for yield. Except for very finely chopped cabbage, the ratio (filling height : basket diameter) should not be less than 1/2. Therefore, if you only have one plant basket, you should pile the distillation material up into the helmet. A dump height with a ratio of about 1 or greater would be ideal, but should then be operated with at least 3000 watts of induction or gas power.
In the case of the stills with a plant basket, it is usually sufficient if 1 to 1.5 liters of distillate are removed when they are full. This should best be done in 2 to 3 batches of 500 ml each. With 2 plant baskets you can roughly double these quantities. Due to the higher heating power required for this, however, the distillation time does not double.
With oleaginous plants, the oil comes out almost all in the 1st margin. In any case, the distillation can be stopped when the distillate no longer smells intense or has a pH value of over 6. In some plants, e.g. B. fennel seeds, depending on the quality of the material, 3 to 4 liters of distillate can be extracted, and the hydrosol still smells intensely and the pH value has not yet reached 6.
The hydrolate must be stored in well-cleaned or sterile, light-protected bottles. The bottles are stored as cool as possible. The hydrolat will continue to mature over the next 4 to 6 weeks, and the smell will become more pleasant and round. One can follow this process by olfactory testing from time to time. However, do not leave the bottle open for too long so that no germs can get in.