2 litres hobby-distillery made from stainless steel for production of essential oils and spirits - registration free
DESTILLIERMEISTER Hobby-E2
Construction of optimized distilleries for over 10 years A registration-free hobby still made of stainless steel. With this beautiful distillery you can make hydrolates, essential oils and distilled water. Easy to use: • approx. Pour 1.7 liters of distilled water into the kettle, • put on the drug basket • fill with herbs or drugs, do not compress, • insert gasket as described below, • put on cover 3. and tighten tension locks 1.1, • insert the distillation bridge 4 into the socket 3.1, • Screw the water hoses to the radiator, connect one end (4.4) to a submersible pump (eg aquarium pump), and the other end (4.5) into the cooling water reservoir. • switch on the heat source and collect at 4.6 hydrolate and oil, • Distill for a maximum of 30 minutes at medium to high heat. The distilling pot and all distillate pipelines are made of stainless steel. The socket for the distillation bridge is made of gunmetal.
The DILLILLIERMEISTER Hobby-E2 is easy to handle. It is ready to use in a few simple steps. For heating, place the distillery on an induction plate. For cooling you need a pot, bucket or bowl of cold water - 10 liters should be enough. With a simple, low-power pump (such as aquarium pump), you can direct water from the reservoir to port 4.4. The hot water leaves the cooling above 4.5. They redirect it back to their water container. Since the cooler is amply sized for its task, a small water flow is sufficient for the cooling.
Construction
Construction of optimized distilleries for over 10 years A registration-free hobby still made of stainless steel. With this beautiful distillery you can make hydrolates, essential oils and distilled water. Easy to use: • approx. Pour 1.7 liters of distilled water into the kettle, • put on the drug basket • fill with herbs or drugs, do not compress, • insert gasket as described below, • put on cover 3. and tighten tension locks 1.1, • insert the distillation bridge 4 into the socket 3.1, • Screw the water hoses to the radiator, connect one end (4.4) to a submersible pump (eg aquarium pump), and the other end (4.5) into the cooling water reservoir. • switch on the heat source and collect at 4.6 hydrolate and oil, • Distill for a maximum of 30 minutes at medium to high heat. The distilling pot and all distillate pipelines are made of stainless steel. The socket for the distillation bridge is made of gunmetal.
The DILLILLIERMEISTER Hobby-E2 is easy to handle. It is ready to use in a few simple steps. For heating, place the distillery on an induction plate. For cooling you need a pot, bucket or bowl of cold water - 10 liters should be enough. With a simple, low-power pump (such as aquarium pump), you can direct water from the reservoir to port 4.4. The hot water leaves the cooling above 4.5. They redirect it back to their water container. Since the cooler is amply sized for its task, a small water flow is sufficient for the cooling.
- Water / steam boiler, 2 liters. It is about 1.7 liters of water, best distilled, filled in the pot.
- Snip nipple for connecting the tension locks 6.
- Herb / Drug Basket, about 2.5 liters capacity
- Lid with socket for the distillation bridge 4.
- Steckbuchse
- Destillierbrücke
- Steigrohr,
- Thermometerbuchse,
- Double pipe cooler in countercurrent (outside jacket, inside soul),
- Kühlwasserzulauf,
- Heißwasserablauf,
- Destillatauslauf.
- Distillation laboratory thermometer with plug for insertion in 4.2.
- Silicone plug with matching hole,
- Distillation thermometer. The thermometer is inserted from the top, thick end of the plug and pushed through until the black mark on the thermometer looks just down straight out. Apply some cooking oil to the thermometer before inserting the thermometer at the lower colored end. After distillation, the thermometer remains best in the stopper, because it is easy to break when pulled out.
- 4 Locking latches for screwing on 1.1.